All heatsinks were firmly attached, so I didn't remove them and risk damage.
The unmarked processor is located under the heatsink circled in the above image.
FTP services and Telnet access to the router is not permitted. Having determined specific requirements, decide if all other traffic is to be allowed or denied. o Standard: closest to destination (if have administrative authority on that router) o Extended: closest to source (if have administrative authority on that router) b. ip access-list extended Server-Access remark Allow PC1 access to server permit tcp host 10.0.0.10 host 172.17.1.1 eq ftp www remark Allow PC2 to access web server permit tcp host 10.0.0.201 host 172.17.1.1 eq www remark Allow PC1 to telnet router permit tcp host 10.0.0.10 host 10.0.0.1 eq telnet remark Deny all other traffic deny ip any any ! Referring to the topology diagram, connect the console (or rollover) cable to the console port on the switch and the other cable end to the host computer with a DB-9 or DB-25 adapter to the COM 1 port. Set interfaces Fa0/1 and Fa0/2 to VLAN 10 by issuing the following commands from the global configuration and interface configuration modes: FC_ASW-1(config)#interface Fast Ethernet0/1 FC_ASW-1(config-if)#switchport access vlan 10 % Access VLAN does not exist. Examine the entries in the Wireshark Packet List (upper) Pane. Satu ARP merequest dan satu ARP mereply perangkat VLAN pada komputer List the source IP addresses: Tergantung pada PC masing-masing What is the difference between the captured ARP packets for each PC this time and those captured in Task 1? Step 4: Clean up Erase the configuration and reload the switch. For PC hosts that are normally connected to other networks (such as the school LAN or to the Internet), reconnect the appropriate cabling and restore the TCP/IP settings. Discuss the use of VLANS in keeping data traffic separated. – mengurani tekanan pada bandwidth dengan membatasi broadcast hanya pada host pada VLAN – menyediakan keamanan dan penyaringan trafik dengan membatasi akses pengguna pada satu VLAN b.
List the benefits and potential problems to the following filtering scenarios: Benefits of allowing all other traffic: Jawab : layanan yang ada untuk ke depannya tidak dihalangi atau diblokir Potential problems with allowing all other traffic: Jawab : Trafik berbahaya dan tidak diinginkan tidak diblok Benefits of denying all other traffic: Jawab : Trafik yang berbahaya dan tidak diinginkan diblok secara otomatis Potential problems with denying all other traffic: Jawab : Layanan yang diimplementasikan ke depannya akan diblok secara otomatis. Consider the two approaches to writing ACLs: When would it be best to permit specific traffic first and then deny general traffic? interface Serial0/1/0 no ip address shutdown clock rate 125000 ! Ensure that power has been applied to both the host computer and switch. Establish a Hyper Terminal, or other terminal emulation program, connection from PC1 to the switch. Ensure that the switch is ready for lab configuration by verifying that all existing VLAN and general configurations are removed. Creating vlan 10 FC_ASW-1(config-if)#interface Fast Ethernet0/2 FC_ASW-1(config-if)#switchport access vlan 10 c. Hanya permintaan ARP yang diterima dari perangkat pada VLAN yang sama. When designing a network list different criteria that could be used to divide a network into VLANs.
The RV345P is passively cooled, even though it supports eight Po E ports.
It probably helps heat management that the power supply is external. The board contains 256 MB flash, 1 GB RAM, and according to Cisco, "the most powerful processor(s) we have ever used (on the RV series)".
This host must be permitted FTP and HTTP access to the network server, and telnet access to the router FC-CPE-1. line con 0 line aux 0 line vty 0 4 password telnet login ! Examine the entries in the Wireshark Packet List (upper) Pane. ARP mengirim permintaan dan menbalas request uuntuk masing-masing perangkat yang di- Did each device receive an ARP request from every PC connected to the switch? Exit Wireshark Task 2: Demonstrate Broadcasts within Multiple VLANs Step 1: Configure the VLANs on the switch a.
However, the RV345P is configured via browser-based Graphical User Interface (GUI).Below is a screenshot showing VLAN1 and VLAN7 configured on the RV345P.I connected an 802.1Q-capable access point to port 1, with SSIDs configured for both VLAN 1 and VLAN 7.I was able to connect to both VLANs and get IP addresses from the correct subnet based on the SSID I attached to, validating the RV345P's VLAN tagging capability.Step 1: Analyze the traffic filtering requirements a. For this lab: 1) PC1 is a network administrator’s workstation.